Civil Engineering MCQS

Design of Masonry Structures

Question No. 01
Rich cement mortars are more liable to cracking as compared to lean mortars because rich mortars
have
(A) High shrinkage
(B) Less strength
(C) Both (A) and (B)
(D) None of above
Answer: Option A
Question No. 02
In a cavity wall, both leaves of which are load bearing, the effective thickness is taken as
(A) Sum of thickness of both leaves
(B) Two-third of the sum of thickness of both the leaves
(C) Actual thickness of the stronger leaf
(D) Larger of (B) and (C)
Answer: Option D
Question No. 03
Assertion A : For identical strength, a composite cement-lime mortar is preferred over cement
mortar.
Reason R : Composite cement-lime mortar has higher drying shrinkage than cement mortar.
Select your answer based on the codes given below:
(A) Both A and R is true and R is the correct explanation of A
(B) Both A and R is true but R is not a correct explanation of A
(C) A is true but R is false
(D) A is false but R is true
Answer: Option C
Question No. 04
For earthquake resistant masonry buildings, the vertical distance between openings one above the
other in a load bearing wall shall not be less than
(A) 50 cm
(B) 60 cm
(C) 75 cm
(D) 100 cm
Answer: Option B
Question No. 05
The mode of failure of a very short masonry member having h/t ratio of less than 4 is by
(A) Shear
(B) Vertical tensile splitting
(C) Buckling
(D) Any of the above
Answer: Option A
Question No. 06
Where a structural component or a system is providing lateral support to five or more walls or
columns, the lateral load to be resisted may be taken as _________ of the total vertical load on
the most heavily loaded wall or column in the group
(A) 4 %
(B) 5 %
(C) 6 %
(D) 7 %
Answer: Option D
Question No. 07
Consider the following statements regarding bands to be provided for strengthening masonry
work in masonry buildings constructed in zone III, IV and V.
(i) Lintel band is provided at lintel level on partition walls,
(ii) Gable band is provided at top of gable masonry below the purlins,
(iii) The bands shall be to full width of the wall and not less than 7.5 cm in depth,
(iv) The bands shall be made of reinforced concrete only.
Of these statements, the correct statements are
(A) (i) and (ii)
(B) (i) and (iii)
(C) (ii) and (iv)
(D) (ii) and (iii)
Answer: Option D
Question No. 08
The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor
of
(A) 1.2
(B) 1.4
(C) 1.6
(D) 2.0
Answer: Option C
Question No. 09
The timber floor not spanning on the masonry wall but properly anchored to the wall gives
(A) Lateral restraint but not rotational restraint
(B) Rotational restraint but not lateral restraint
(C) Both lateral and rotational restraints
(D) Neither lateral nor rotational restraint
Answer: Option A
Question No. 10
A free standing brick wall 20 cm thick is subjected to a wind pressure of 75kg/m². The maximum
height of wall from stability consideration is
(A) 0.64 m
(B) 0.96 m
(C) 1.28 m
(D) 1.5 m
Answer: Option A
Question No. 11
Consider the following statements:
The use of relatively weak mortar
1. Will accommodate movements due to loads and, cracking if any, and will be distributed as thin
hair cracks which are less noticeable or harmful.
2. Will result in reduction of stresses due to differential expansion of masonry units.
Of these statements
(A) 1 alone is correct
(B) 2 alone is correct
(C) Both 1 and 2 are correct
(D) Neither 1 nor 2 is correct
Answer: Option C
Question No. 12
If is the height of wall between centers of supports, then the effective height of wall where
concrete floors have a bearing on wall irrespective of the direction of span will be
(A) 0.75 H
(B) 0.85 H
(C) 1.0 H
(D) 1.5 H
Answer: Option A
Question No. 13
For designing masonry components of a structure, seismic forces provision in the design
calculation is not necessary for buildings constructed in
(A) Zone I only
(B) Zone I and II
(C) Zone I, II and III
(D) Zone I, II, III and IV
Answer: Option B
Question No. 14
A 200 mm thick wall made of modular bricks is 5 m long between cross walls and 3.8 m clear
height between RCC slabs at top and bottom. The slenderness ratio of the wall is
(A) 15
(B) 19
(C) 20
(D) 25
Answer: Option A
Question No. 15
Water retentivity for brick masonry should not be less than
(A) 50 %
(B) 60 %
(C) 70 %
(D) 80 %
Answer: Option C
Question No. 16
The bending stress in a wall or column subjected to effective vertical load need not be considered,
if the eccentricity ratio is
(A) Less than or equal to 1/24
(B) Less than or equal to 1/6
(C) More than 1/24
(D) Less than or equal to 1/12
Answer: Option A
Question No. 17
Assertion A : Lime based mortars give higher ratio of brickwork strength to mortar strength as
compared to non-lime mortar.
Reason R : Lime based mortars have lower bond strength as compared to non-lime mortars.
Select your answer according to the codes given below:
(A) Both A and R is true and R is the correct explanation of A
(B) Both A and R is true but R is not the correct explanation of A
(C) A is true but R is false
(D) A is false but R is true
Answer: Option C
Question No. 18
In the case of panel wall subjected to horizontal loads at right angles to the plane of the wall, with
the mortar not leaner than Ml type, tensile stress in bending in the vertical direction may be
allowed to the extent of
(A) 0.4 kg/cm²
(B) 0.7 kg/cm²
(C) 1.0 kg/cm²
(D) 1.2 kg/cm²
Answer: Option C
Question No. 19
If the ratio of center to center spacing of intersecting walls to actual thickness of intersecting wall
is more than 20, then the stiffening coefficient for wall proper will be
(A) 0
(B) Between 0 and 1
(C) 1
(D) Greater than 1
Answer: Option D
Question No. 20
Consider the following statements:
1. Masonry in rich cement mortar though having good strength with high shrinkage is much liable
for surface cracks.
2. Lime mortar possesses poor workability and poor water retentivity and also suffers high
shrinkage.
3. Masonry in lime mortar has better resistance against rain penetration and is less liable to crack
when compared to masonry in cement mortar.
Which of these statements are correct?
(A) 1, 2 and 3
(B) 1 and 2
(C) 2 and 3
(D) 1 and 3
Answer: Option D
Question No. 21
If the eccentricity ratio is more than 1/24, then increase in the permissible stress in the design of
wall subjected to eccentric loading as per code is
(A) 10 %
(B) 25 %
(C)
(D) 50 %
Answer: Option B
Question No. 22
For masonry work with solid bricks, consistency of mortar should be
(A) 5 to 8 cm
(B) 9 to 13 cm
(C) 14 to 18 cm
(D) 19 to 23 cm
Answer: Option B
Question No. 23
Consider the following statements regarding provision of chases in masonry,
(i) No chase should be permitted in a half brick load-bearing wall,
(ii) Vertical chases should not be closer than 2 m in any stretch of a wall,
(iii) Chases should be provided near to bearings of beams and lintels. Of these statements
(A) (i) and (ii) are correct
(B) (i) and (iii) are correct
(C) (ii) and (iii) are correct
(D) (i), (ii) and (iii) are correct
Answer: Option A
Question No. 24
For masonry built in 1 : 1 : 6 cement-lime-sand mix mortar or equivalent, the horizontal shear
stress permissible on the area of a mortar bed joint is
(A) 0.15 MPa
(B) 0.125 MPa
(C) 0.1 MPa
(D) 0.075 MPa
Answer: Option A
Question No. 25
Maximum slenderness ratio of load bearing walls for a dwelling having more than 2 storeys
(i) Shall not exceed 12 if lime mortar is used
(ii) Shall not exceed 18 if cement lime mortar 1 : 2 : 9 is used
(iii) Shall not exceed 24 if cement mortar 1 : 6 is used
Of these statements
(A) (i) and (ii) are correct
(B) (ii) and (iii) are correct
(C) (i) and (iii) are correct
(D) (i) and (ii) and (iii) are correct
Answer: Option A
Question No. 26
Full restraint is provided by
(i) Foundation footing of a wall
(ii) Timber floor spanning on the wall and anchored to the wall
(iii) RCC slab with a minimum bearing of 10 cm on the wall
Of these statements
(A) (i) and (iii) are correct
(B) (i) and (ii) are correct
(C) (ii) and (iii) are correct
(D) (i), (ii) and (iii) are correct
Answer: Option D
Question No. 27
Consider the following statements:
A high lime content in a composite cement-lime mortar results in
1. Slow hardening.
2. Quick setting.
3. Weaker mortar. Of these statements
(A) 2 and 3 are correct
(B) 1 and 2 are correct
(C) 1 and 3 are correct
(D) 1, 2 and 3 are correct
Answer: Option C
Question No. 28
The effective height of free standing non-load bearing wall and column respectively will be
(A) 1.0H and 1.0H
(B) 1.5H and 1.5H
(C) 2.0H and 1.5H
(D) 2.0H and 2.0H
Where H is the height of wall or column between centers of supports
Answer: Option D
Question No. 29
Assertion A : From consideration of structural soundness and economy of design, most codes
control the maximum slenderness ratio of masonry walls and columns.
Reason R : By controlling the maximum slenderness ratio, failure is by excessive stress and not by
buckling. Select your answer according to codes given below:
(A) Both A and R is true and R is the correct explanation of A
(B) Both A and R is true but R is not the correct explanation of A
(C) A is true but R is false
(D) A is false but R is true
Answer: Option A
Question No. 30
Assertion A : Limiting value of slenderness ratio for a column is less than that of a wall.
Reason R : A column can buckle around either of the two horizontal axes while a wall can buckle
around only one axis.
Select your answer according to the codes given below:
(A) Both A and R is true and R is the correct explanation of A
(B) Both A and R is true but R is not the correct explanation of A
(C) A is true but R is false
(D) A is false but R is true
Answer: Option A
Question No. 31
A 200 mm thick brick masonry wall made of modular bricks carries an axial load of 30 kN/m from
wall above and an eccentric load of 20 kN/m from RCC floor acting at a distance of 47.5 mm from
the centre line of the wall. The resultant eccentricity ratio is
(A) 0.090
(B) 0.095
(C) 0.100
(D) 0.105
Answer: Option C
Question No. 32
The thickness of each leaf of a cavity wall shall not be less than
(A) 5 cm
(B) 7.5 cm
(C) 10 cm
(D) 15 cm
Answer: Option B
Question No. 33
Minimum compressive strength in N/mm² for H1 type mortar used for masonry is
(A) 3
(B) 5
(C) 7.5
(D) 10
Answer: Option D
Question No. 34
Direct load carrying capacity of a brick masonry wall standing freely as against when it supports RC
slab will be
(A) More
(B) Less
(C) The same in both the cases
(D) 100 %
Answer: Option B
Question No. 35
Assertion A : For eccentricity ratio exceeding 1/6, effective thickness of masonry will get reduced.
Reason R : For eccentricity ratio exceeding 1/6, there will be tension on one side of the member.
Select your answer according to the codes give below:
(A) Both A and R is true and R is the correct explanation of A
(B) Both A and R is true and R is not the correct explanation of A
(C) A is true but R is false
(D) A is false but R is true
Answer: Option A
Question No. 36
If the horizontal cross-sectional area of a wall is 1200 cm², then the basic stress shall be multiplied
by a reduction factor equal to
(A) 0 6
(B) 0.75
(C) 0.85
(D) 0.95
Answer: Option C
Question No. 37
For strengthening a 50 m long and 5 m high straight compound wall built in brick work, which one
of the following would be most suitable?
(A) Providing buttresses at certain intervals
(B) Providing a deeper foundation
(C) Using a richer mortar
(D) Using stronger bricks
Answer: Option A
Question No. 38
Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than
(A) 10 cm
(B) 15 cm
(C) 20 cm
(D) 30 cm
Answer: Option A
Question No. 39
Cement mortars richer than 1 : 3 are not used in masonry because
(i) There is no gain in strength of masonry
(ii) There is high shrinkage
(iii) They are prone to segregation
Of these statements
(A) Only (ii) is correct
(B) (i) and (ii) are correct
(C) (ii) and (iii) are correct
(D) (i), (ii) and (iii) are correct
Answer: Option B